Lift-It

One of the most versatile nylon web slings available, Endless slings can be rotated to provide an infinite number of contact points for the ends of the endless lifting strap and where the endless sling lift strap contacts the load. Endless hoisting slings and straps are for use in choker, vertical and basket hitches. Endless sling strap ends can be tapered and reinforced on request. Endless polyester and nylon sling straps are also referred to as continuous loop slings, type 5 slings and/or grommet slings. Lift-It® Endless slings are available in either nylon or polyester webbing, polyester is the standard material on all models. The length of an endless web sling is measured pull to pull or bearing to bearing on the ends of the endless nylon lift strap, not circumferentially. Polyester web and Nylon web endless slings are formed by overlapping the ends of the heavy duty webbing to form a load carrying splice. It is recommended when using endless sling straps that the load carrying splice NOT be placed into the load or lift connection points. Likewise, when Endless slings are used in a choker hitch it is recommended that the load carrying splice be placed above the choker point and below the lifting fixture. If an endless sling configuration is desired that does not feature a load carrying splice, we’d recommend the use of a polyester roundsling. Polyester round slings are also sometimes referred to as spansets. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point unless otherwise specified. Eye & Eye nylon & polyester lifting slings featuring flat eyes can be used in all three hitches: choker, vertical and basket. Heavy duty nylon rigging slings featuring the Flat Eye and Eye design are made in widths ranging from as narrow as 1 inch and as wide as 12 inches. All Lift-It® Flat Eye & Eye slings feature protection at the sling eye bearing points. The extra protection wrapped around the sling eye provides additional service life as this is a critical wear area for all polyester and nylon rigging slings. Sling eyes are automatically tapered to a narrower width on Eye and Eye lifting slings that are over 3 inches in width. At Lift-It we do not charge extra to taper the eyes for your 2 inch wide rigging straps. Flat Eye, Eye and Eye nylon lifting slings used by crane and rigging customers around the world provide for the lowest profile eye available. Low profile eyes make sling removal easier when tight clearances are unavoidable. Nylon rigging slings that feature flat eyes are also referred to as double eye slings or Type 3 slings. If a more supple body composition is desired consider using Lift-It® polyester roundslings in the eye and eye style. Eye & Eye polyester round slings are formed by passing an exterior sleeve over the strands of the polyester roundsling. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point unless otherwise specified. Eye & Eye nylon & polyester lifting slings featuring flat eyes can be used in all three hitches: choker, vertical and basket. Heavy duty nylon rigging slings featuring the Flat Eye and Eye design are made in widths ranging from as narrow as 1 inch and as wide as 12 inches. All Lift-It® Flat Eye & Eye slings feature protection at the sling eye bearing points. The extra protection wrapped around the sling eye provides additional service life as this is a critical wear area for all polyester and nylon rigging slings. Sling eyes are automatically tapered to a narrower width on Eye and Eye lifting slings that are over 3 inches in width. At Lift-It we do not charge extra to taper the eyes for your 2 inch wide rigging straps. Flat Eye, Eye and Eye nylon lifting slings used by crane and rigging customers around the world provide for the lowest profile eye available. Low profile eyes make sling removal easier when tight clearances are unavoidable. Nylon rigging slings that feature flat eyes are also referred to as double eye slings or Type 3 slings. If a more supple body composition is desired consider using Lift-It® polyester roundslings in the eye and eye style. Eye & Eye polyester round slings are formed by passing an exterior sleeve over the strands of the polyester roundsling. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point unless otherwise specified. Eye & Eye nylon & polyester lifting slings featuring flat eyes can be used in all three hitches: choker, vertical and basket. Heavy duty nylon rigging slings featuring the Flat Eye and Eye design are made in widths ranging from as narrow as 1 inch and as wide as 12 inches. All Lift-It® Flat Eye & Eye slings feature protection at the sling eye bearing points. The extra protection wrapped around the sling eye provides additional service life as this is a critical wear area for all polyester and nylon rigging slings. Sling eyes are automatically tapered to a narrower width on Eye and Eye lifting slings that are over 3 inches in width. At Lift-It we do not charge extra to taper the eyes for your 2 inch wide rigging straps. Flat Eye, Eye and Eye nylon lifting slings used by crane and rigging customers around the world provide for the lowest profile eye available. Low profile eyes make sling removal easier when tight clearances are unavoidable. Nylon rigging slings that feature flat eyes are also referred to as double eye slings or Type 3 slings. If a more supple body composition is desired consider using Lift-It® polyester roundslings in the eye and eye style. Eye & Eye polyester round slings are formed by passing an exterior sleeve over the strands of the polyester roundsling. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point unless otherwise specified. Eye & Eye nylon & polyester lifting slings featuring flat eyes can be used in all three hitches: choker, vertical and basket. Heavy duty nylon rigging slings featuring the Flat Eye and Eye design are made in widths ranging from as narrow as 1 inch and as wide as 12 inches. All Lift-It® Flat Eye & Eye slings feature protection at the sling eye bearing points. The extra protection wrapped around the sling eye provides additional service life as this is a critical wear area for all polyester and nylon rigging slings. Sling eyes are automatically tapered to a narrower width on Eye and Eye lifting slings that are over 3 inches in width. At Lift-It we do not charge extra to taper the eyes for your 2 inch wide rigging straps. Flat Eye, Eye and Eye nylon lifting slings used by crane and rigging customers around the world provide for the lowest profile eye available. Low profile eyes make sling removal easier when tight clearances are unavoidable. Nylon rigging slings that feature flat eyes are also referred to as double eye slings or Type 3 slings. If a more supple body composition is desired consider using Lift-It® polyester roundslings in the eye and eye style. Eye & Eye polyester round slings are formed by passing an exterior sleeve over the strands of the polyester roundsling. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point unless otherwise specified. Eye & Eye nylon & polyester lifting slings featuring flat eyes can be used in all three hitches: choker, vertical and basket. Heavy duty nylon rigging slings featuring the Flat Eye and Eye design are made in widths ranging from as narrow as 1 inch and as wide as 12 inches. All Lift-It® Flat Eye & Eye slings feature protection at the sling eye bearing points. The extra protection wrapped around the sling eye provides additional service life as this is a critical wear area for all polyester and nylon rigging slings. Sling eyes are automatically tapered to a narrower width on Eye and Eye lifting slings that are over 3 inches in width. At Lift-It we do not charge extra to taper the eyes for your 2 inch wide rigging straps. Flat Eye, Eye and Eye nylon lifting slings used by crane and rigging customers around the world provide for the lowest profile eye available. Low profile eyes make sling removal easier when tight clearances are unavoidable. Nylon rigging slings that feature flat eyes are also referred to as double eye slings or Type 3 slings. If a more supple body composition is desired consider using Lift-It® polyester roundslings in the eye and eye style. Eye & Eye polyester round slings are formed by passing an exterior sleeve over the strands of the polyester roundsling. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point unless otherwise specified. Eye & Eye nylon & polyester lifting slings featuring flat eyes can be used in all three hitches: choker, vertical and basket. Heavy duty nylon rigging slings featuring the Flat Eye and Eye design are made in widths ranging from as narrow as 1 inch and as wide as 12 inches. All Lift-It® Flat Eye & Eye slings feature protection at the sling eye bearing points. The extra protection wrapped around the sling eye provides additional service life as this is a critical wear area for all polyester and nylon rigging slings. Sling eyes are automatically tapered to a narrower width on Eye and Eye lifting slings that are over 3 inches in width. At Lift-It we do not charge extra to taper the eyes for your 2 inch wide rigging straps. Flat Eye, Eye and Eye nylon lifting slings used by crane and rigging customers around the world provide for the lowest profile eye available. Low profile eyes make sling removal easier when tight clearances are unavoidable. Nylon rigging slings that feature flat eyes are also referred to as double eye slings or Type 3 slings. If a more supple body composition is desired consider using Lift-It® polyester roundslings in the eye and eye style. Eye & Eye polyester round slings are formed by passing an exterior sleeve over the strands of the polyester roundsling. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Equipment recovery in surface mining operations has been improved dramatically, with the use of Lift-It® High Performance Fiber, Twin-Path® Mine Tow Straps.

Equipment recovery in surface mining operations has been improved dramatically, with the use of Lift-It® High Performance Fiber, Twin-Path® Mine Tow Straps.

Endless slings are a versatile sling as hook and load contact points can be rotated. For use in choker, vertical and basket hitches. Sling ends can be tapered and reinforced on request.

Endless slings are a versatile sling as hook and load contact points can be rotated. For use in choker, vertical and basket hitches. Sling ends can be tapered and reinforced on request.

Endless slings are a versatile sling as hook and load contact points can be rotated. For use in choker, vertical and basket hitches. Sling ends can be tapered and reinforced on request.

Endless slings are a versatile sling as hook and load contact points can be rotated. For use in choker, vertical and basket hitches. Sling ends can be tapered and reinforced on request.

Polyester Max Edge™ Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point (Order Code J), unless otherwise specified.

Polyester Max Edge™ Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point (Order Code J), unless otherwise specified.

Polyester Max Edge™ Eye and Eye slings can be used in choker, vertical and basket hitches. Slings with Half Twist (Type 4) eyes are furnished unless Flat (Type 3) eyes are specified. Sling eyes will be wrapped at the bearing point (Order Code J), unless otherwise specified.

(MLB4) Four Leg Bridle Assembly capacities are based on three legs carrying the assigned capacity. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

(MLB4) Four Leg Bridle Assembly capacities are based on three legs carrying the assigned capacity. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Sleeves cover both sides of the sling and can be moved to a specific location. Sleeves can also be re-positioned for quick and easy inspection of the sling.

Lift-It® Felt Sleeves blend two wear protection materials: Polyester Felt covered by Bulked Nylon, chap sleeves.

Felt Sleeves with Velcro provide protection from abrasion damage caused by contact with rough surfaces.

Felt Sleeves with Velcro provide protection from abrasion damage caused by contact with rough surfaces.

Felt Sleeves with Velcro provide protection from abrasion damage caused by contact with rough surfaces.

Sleeves cover both sides of the sling and can be moved to a specific location. Sleeves can also be re-positioned for quick and easy inspection of the sling.

Reversed Eye slings are nylon web slings which feature sling eyes and body that are covered by Bulked Nylon, also referred to as Cordura®, wear pads. Bulked Nylon wear pad material is four times more abrasion resistant than webbing used in regular nylon lifting slings, but provides no protection against cutting. The Reversed Eye lift strap is also referred to as a Return Eye sling. Since the body of Reversed Eye slings is based upon an endless sling design, the web strap eye is one half the overall body width. The sling eye can further be reduced by tapering the sling eye before installing the Cordura® wear pads on each side of the sling body. When you receive the Reversed Eye sling, the sling capacity tag is on the side OPPOSITE the working face or load contact surface of the sling. Responsible sling users in the sling, rigging and material handling industries always inspect the sling before each use. When abrasion is detected that does not penetrate into the load bearing sling webbing the sling user can rotate or “reverse” the sling eyes, which also provides a new bearing surface on the sling body. The bearing points of Reversed Eye hoisting sling-Standard (Type 6) eyes are 90° to the web sling body. The perpendicular relationship between the eye and body in a Reversed Eye lifting sling-Standard (Type 6) results in a better choke hitch, when compared to the Reversed Eye hoisting sling-Flat (Type 7). The Reversed Eye sling-Flat (Type 7) body is turned 180°, forming an eye, in the same plane as the sling body. The type 7 or flat Reverse Eye web sling is not frequently made, but provides a lower profile lifting sling for removal when space is limited. Type 6 and Type 7 Reversed Eye web slings can be used in choker, vertical or basket hitches. Standard widths for Reversed eye nylon web slings range from 2 inches to 6 inches. On request we can manufacture 8, 10 and 12 inch wide Reverse Eye lifting slings. Stock numbers for Reverse Eye slings do not reflect the overall sling width, but refer to the width of the component webbing, laid side by side to form up the body of the Reversed Eye lifting strap. An example would be, RE2-902 which would be the call out for a Reversed Eye web sling that is made from heavy duty nylon sling material (9800 Lbs. unsewn tensile strength- Class 7), 2 inches wide and two ply thick. The 2 inch material is sewn into an endless web sling configuration with the strands of the endless set side by side. After the eye buffers have been sewn to each side of the sling eye, 4 inch material is used to finish the fabrication of the nylon lifting sling. Sometimes it’s a hard sell to convince sling users that it is a better investment to spend more for a Reversed Eye sling. Reversed Eye web slings are roughly twice the price of an equivalent strength Eye and Eye sling. The combination of wear resistant materials, coupled with the ability to change out the bearing surfaces on the sling eyes and bodies make the Reversed Eye hoisting strap, the nylon sling of choice for professionals in the heavy duty sling, rigging and crane industries. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Reversed Eye slings are nylon web slings which feature sling eyes and body that are covered by Bulked Nylon, also referred to as Cordura®, wear pads. Bulked Nylon wear pad material is four times more abrasion resistant than webbing used in regular nylon lifting slings, but provides no protection against cutting. The Reversed Eye lift strap is also referred to as a Return Eye sling. Since the body of Reversed Eye slings is based upon an endless sling design, the web strap eye is one half the overall body width. The sling eye can further be reduced by tapering the sling eye before installing the Cordura® wear pads on each side of the sling body. When you receive the Reversed Eye sling, the sling capacity tag is on the side OPPOSITE the working face or load contact surface of the sling. Responsible sling users in the sling, rigging and material handling industries always inspect the sling before each use. When abrasion is detected that does not penetrate into the load bearing sling webbing the sling user can rotate or “reverse” the sling eyes, which also provides a new bearing surface on the sling body. The bearing points of Reversed Eye hoisting sling-Standard (Type 6) eyes are 90° to the web sling body. The perpendicular relationship between the eye and body in a Reversed Eye lifting sling-Standard (Type 6) results in a better choke hitch, when compared to the Reversed Eye hoisting sling-Flat (Type 7). The Reversed Eye sling-Flat (Type 7) body is turned 180°, forming an eye, in the same plane as the sling body. The type 7 or flat Reverse Eye web sling is not frequently made, but provides a lower profile lifting sling for removal when space is limited. Type 6 and Type 7 Reversed Eye web slings can be used in choker, vertical or basket hitches. Standard widths for Reversed eye nylon web slings range from 2 inches to 6 inches. On request we can manufacture 8, 10 and 12 inch wide Reverse Eye lifting slings. Stock numbers for Reverse Eye slings do not reflect the overall sling width, but refer to the width of the component webbing, laid side by side to form up the body of the Reversed Eye lifting strap. An example would be, RE2-902 which would be the call out for a Reversed Eye web sling that is made from heavy duty nylon sling material (9800 Lbs. unsewn tensile strength- Class 7), 2 inches wide and two ply thick. The 2 inch material is sewn into an endless web sling configuration with the strands of the endless set side by side. After the eye buffers have been sewn to each side of the sling eye, 4 inch material is used to finish the fabrication of the nylon lifting sling. Sometimes it’s a hard sell to convince sling users that it is a better investment to spend more for a Reversed Eye sling. Reversed Eye web slings are roughly twice the price of an equivalent strength Eye and Eye sling. The combination of wear resistant materials, coupled with the ability to change out the bearing surfaces on the sling eyes and bodies make the Reversed Eye hoisting strap, the nylon sling of choice for professionals in the heavy duty sling, rigging and crane industries. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Reversed Eye slings are nylon web slings which feature sling eyes and body that are covered by Bulked Nylon, also referred to as Cordura®, wear pads. Bulked Nylon wear pad material is four times more abrasion resistant than webbing used in regular nylon lifting slings, but provides no protection against cutting. The Reversed Eye lift strap is also referred to as a Return Eye sling. Since the body of Reversed Eye slings is based upon an endless sling design, the web strap eye is one half the overall body width. The sling eye can further be reduced by tapering the sling eye before installing the Cordura® wear pads on each side of the sling body. When you receive the Reversed Eye sling, the sling capacity tag is on the side OPPOSITE the working face or load contact surface of the sling. Responsible sling users in the sling, rigging and material handling industries always inspect the sling before each use. When abrasion is detected that does not penetrate into the load bearing sling webbing the sling user can rotate or “reverse” the sling eyes, which also provides a new bearing surface on the sling body. The bearing points of Reversed Eye hoisting sling-Standard (Type 6) eyes are 90° to the web sling body. The perpendicular relationship between the eye and body in a Reversed Eye lifting sling-Standard (Type 6) results in a better choke hitch, when compared to the Reversed Eye hoisting sling-Flat (Type 7). The Reversed Eye sling-Flat (Type 7) body is turned 180°, forming an eye, in the same plane as the sling body. The type 7 or flat Reverse Eye web sling is not frequently made, but provides a lower profile lifting sling for removal when space is limited. Type 6 and Type 7 Reversed Eye web slings can be used in choker, vertical or basket hitches. Standard widths for Reversed eye nylon web slings range from 2 inches to 6 inches. On request we can manufacture 8, 10 and 12 inch wide Reverse Eye lifting slings. Stock numbers for Reverse Eye slings do not reflect the overall sling width, but refer to the width of the component webbing, laid side by side to form up the body of the Reversed Eye lifting strap. An example would be, RE2-902 which would be the call out for a Reversed Eye web sling that is made from heavy duty nylon sling material (9800 Lbs. unsewn tensile strength- Class 7), 2 inches wide and two ply thick. The 2 inch material is sewn into an endless web sling configuration with the strands of the endless set side by side. After the eye buffers have been sewn to each side of the sling eye, 4 inch material is used to finish the fabrication of the nylon lifting sling. Sometimes it’s a hard sell to convince sling users that it is a better investment to spend more for a Reversed Eye sling. Reversed Eye web slings are roughly twice the price of an equivalent strength Eye and Eye sling. The combination of wear resistant materials, coupled with the ability to change out the bearing surfaces on the sling eyes and bodies make the Reversed Eye hoisting strap, the nylon sling of choice for professionals in the heavy duty sling, rigging and crane industries. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Reversed Eye slings are nylon web slings which feature sling eyes and body that are covered by Bulked Nylon, also referred to as Cordura®, wear pads. Bulked Nylon wear pad material is four times more abrasion resistant than webbing used in regular nylon lifting slings, but provides no protection against cutting. The Reversed Eye lift strap is also referred to as a Return Eye sling. Since the body of Reversed Eye slings is based upon an endless sling design, the web strap eye is one half the overall body width. The sling eye can further be reduced by tapering the sling eye before installing the Cordura® wear pads on each side of the sling body. When you receive the Reversed Eye sling, the sling capacity tag is on the side OPPOSITE the working face or load contact surface of the sling. Responsible sling users in the sling, rigging and material handling industries always inspect the sling before each use. When abrasion is detected that does not penetrate into the load bearing sling webbing the sling user can rotate or “reverse” the sling eyes, which also provides a new bearing surface on the sling body. The bearing points of Reversed Eye hoisting sling-Standard (Type 6) eyes are 90° to the web sling body. The perpendicular relationship between the eye and body in a Reversed Eye lifting sling-Standard (Type 6) results in a better choke hitch, when compared to the Reversed Eye hoisting sling-Flat (Type 7). The Reversed Eye sling-Flat (Type 7) body is turned 180°, forming an eye, in the same plane as the sling body. The type 7 or flat Reverse Eye web sling is not frequently made, but provides a lower profile lifting sling for removal when space is limited. Type 6 and Type 7 Reversed Eye web slings can be used in choker, vertical or basket hitches. Standard widths for Reversed eye nylon web slings range from 2 inches to 6 inches. On request we can manufacture 8, 10 and 12 inch wide Reverse Eye lifting slings. Stock numbers for Reverse Eye slings do not reflect the overall sling width, but refer to the width of the component webbing, laid side by side to form up the body of the Reversed Eye lifting strap. An example would be, RE2-902 which would be the call out for a Reversed Eye web sling that is made from heavy duty nylon sling material (9800 Lbs. unsewn tensile strength- Class 7), 2 inches wide and two ply thick. The 2 inch material is sewn into an endless web sling configuration with the strands of the endless set side by side. After the eye buffers have been sewn to each side of the sling eye, 4 inch material is used to finish the fabrication of the nylon lifting sling. Sometimes it’s a hard sell to convince sling users that it is a better investment to spend more for a Reversed Eye sling. Reversed Eye web slings are roughly twice the price of an equivalent strength Eye and Eye sling. The combination of wear resistant materials, coupled with the ability to change out the bearing surfaces on the sling eyes and bodies make the Reversed Eye hoisting strap, the nylon sling of choice for professionals in the heavy duty sling, rigging and crane industries. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Reversed Eye slings are nylon web slings which feature sling eyes and body that are covered by Bulked Nylon, also referred to as Cordura®, wear pads. Bulked Nylon wear pad material is four times more abrasion resistant than webbing used in regular nylon lifting slings, but provides no protection against cutting. The Reversed Eye lift strap is also referred to as a Return Eye sling. Since the body of Reversed Eye slings is based upon an endless sling design, the web strap eye is one half the overall body width. The sling eye can further be reduced by tapering the sling eye before installing the Cordura® wear pads on each side of the sling body. When you receive the Reversed Eye sling, the sling capacity tag is on the side OPPOSITE the working face or load contact surface of the sling. Responsible sling users in the sling, rigging and material handling industries always inspect the sling before each use. When abrasion is detected that does not penetrate into the load bearing sling webbing the sling user can rotate or “reverse” the sling eyes, which also provides a new bearing surface on the sling body. The bearing points of Reversed Eye hoisting sling-Standard (Type 6) eyes are 90° to the web sling body. The perpendicular relationship between the eye and body in a Reversed Eye lifting sling-Standard (Type 6) results in a better choke hitch, when compared to the Reversed Eye hoisting sling-Flat (Type 7). The Reversed Eye sling-Flat (Type 7) body is turned 180°, forming an eye, in the same plane as the sling body. The type 7 or flat Reverse Eye web sling is not frequently made, but provides a lower profile lifting sling for removal when space is limited. Type 6 and Type 7 Reversed Eye web slings can be used in choker, vertical or basket hitches. Standard widths for Reversed eye nylon web slings range from 2 inches to 6 inches. On request we can manufacture 8, 10 and 12 inch wide Reverse Eye lifting slings. Stock numbers for Reverse Eye slings do not reflect the overall sling width, but refer to the width of the component webbing, laid side by side to form up the body of the Reversed Eye lifting strap. An example would be, RE2-902 which would be the call out for a Reversed Eye web sling that is made from heavy duty nylon sling material (9800 Lbs. unsewn tensile strength- Class 7), 2 inches wide and two ply thick. The 2 inch material is sewn into an endless web sling configuration with the strands of the endless set side by side. After the eye buffers have been sewn to each side of the sling eye, 4 inch material is used to finish the fabrication of the nylon lifting sling. Sometimes it’s a hard sell to convince sling users that it is a better investment to spend more for a Reversed Eye sling. Reversed Eye web slings are roughly twice the price of an equivalent strength Eye and Eye sling. The combination of wear resistant materials, coupled with the ability to change out the bearing surfaces on the sling eyes and bodies make the Reversed Eye hoisting strap, the nylon sling of choice for professionals in the heavy duty sling, rigging and crane industries. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Reversed Eye slings are nylon web slings which feature sling eyes and body that are covered by Bulked Nylon, also referred to as Cordura®, wear pads. Bulked Nylon wear pad material is four times more abrasion resistant than webbing used in regular nylon lifting slings, but provides no protection against cutting. The Reversed Eye lift strap is also referred to as a Return Eye sling. Since the body of Reversed Eye slings is based upon an endless sling design, the web strap eye is one half the overall body width. The sling eye can further be reduced by tapering the sling eye before installing the Cordura® wear pads on each side of the sling body. When you receive the Reversed Eye sling, the sling capacity tag is on the side OPPOSITE the working face or load contact surface of the sling. Responsible sling users in the sling, rigging and material handling industries always inspect the sling before each use. When abrasion is detected that does not penetrate into the load bearing sling webbing the sling user can rotate or “reverse” the sling eyes, which also provides a new bearing surface on the sling body. The bearing points of Reversed Eye hoisting sling-Standard (Type 6) eyes are 90° to the web sling body. The perpendicular relationship between the eye and body in a Reversed Eye lifting sling-Standard (Type 6) results in a better choke hitch, when compared to the Reversed Eye hoisting sling-Flat (Type 7). The Reversed Eye sling-Flat (Type 7) body is turned 180°, forming an eye, in the same plane as the sling body. The type 7 or flat Reverse Eye web sling is not frequently made, but provides a lower profile lifting sling for removal when space is limited. Type 6 and Type 7 Reversed Eye web slings can be used in choker, vertical or basket hitches. Standard widths for Reversed eye nylon web slings range from 2 inches to 6 inches. On request we can manufacture 8, 10 and 12 inch wide Reverse Eye lifting slings. Stock numbers for Reverse Eye slings do not reflect the overall sling width, but refer to the width of the component webbing, laid side by side to form up the body of the Reversed Eye lifting strap. An example would be, RE2-902 which would be the call out for a Reversed Eye web sling that is made from heavy duty nylon sling material (9800 Lbs. unsewn tensile strength- Class 7), 2 inches wide and two ply thick. The 2 inch material is sewn into an endless web sling configuration with the strands of the endless set side by side. After the eye buffers have been sewn to each side of the sling eye, 4 inch material is used to finish the fabrication of the nylon lifting sling. Sometimes it’s a hard sell to convince sling users that it is a better investment to spend more for a Reversed Eye sling. Reversed Eye web slings are roughly twice the price of an equivalent strength Eye and Eye sling. The combination of wear resistant materials, coupled with the ability to change out the bearing surfaces on the sling eyes and bodies make the Reversed Eye hoisting strap, the nylon sling of choice for professionals in the heavy duty sling, rigging and crane industries. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Sleeves cover both sides of the sling and can be moved to a specific location. Sleeves can also be re-positioned for quick and easy inspection of the sling.

Lift-It® Felt Sleeves blend two wear protection materials: Polyester Felt covered by Bulked Nylon, chap sleeves.

Felt Sleeves provide protection from abrasion damage caused by contact with rough surfaces.

Felt Sleeves provide protection from abrasion damage caused by contact with rough surfaces.

Felt Sleeves provide protection from abrasion damage caused by contact with rough surfaces.

Sleeves cover both sides of the sling and can be moved to a specific location. Sleeves can also be re-positioned for quick and easy inspection of the sling.

Basket Hardware Slings feature fittings of aluminum (ABH) or alloy steel (SBH). Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Basket Hardware Slings feature fittings of aluminum (ABH) or alloy steel (SBH). Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Basket Hardware Slings feature fittings of aluminum (ABH) or alloy steel (SBH). Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Basket Hardware Slings feature fittings of aluminum (ABH) or alloy steel (SBH). Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Basket Hardware Slings feature fittings of aluminum (ABH) or alloy steel (SBH). Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Basket Hardware Slings feature fittings of aluminum (ABH) or alloy steel (SBH). Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Aluminum and alloy steel choker fittings provide for the most efficient choke hitching available for webbing slings. Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Aluminum and alloy steel choker fittings provide for the most efficient choke hitching available for webbing slings. Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Aluminum and alloy steel choker fittings provide for the most efficient choke hitching available for webbing slings. Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Aluminum and alloy steel choker fittings provide for the most efficient choke hitching available for webbing slings. Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Aluminum and alloy steel choker fittings provide for the most efficient choke hitching available for webbing slings. Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Aluminum and alloy steel choker fittings provide for the most efficient choke hitching available for webbing slings. Steel fittings are automatically supplied on two and four ply slings. Recycle your fittings for cost savings. Exposure to acids, alkalis or other corrosive agents must be evaluated prior to use. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Lift-It® Bridle Assembly capacities are lower than our competitors. (MLB3)Three Leg Bridle Assembly capacities are based upon 2-1/2 legs carrying the assigned capacity. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.

Lift-It® Bridle Assembly capacities are lower than our competitors. (MLB3)Three Leg Bridle Assembly capacities are based upon 2-1/2 legs carrying the assigned capacity. If a 200% load test is required on your slings please contact our sales team prior to ordering, 909-469-2251.